/usr/share/doc/tgt/examples/targets.conf.vtl.MSL2024 is in tgt 1:1.0.51-1.
This file is owned by root:root, with mode 0o644.
The actual contents of the file can be viewed below.
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 | # Virtual tape library example for an HP MSL-2024 tape library
#
# In this case, tapes are stored in the directory /root/tapes
# size is in MB (1 GB in this case)
# using the command "tgtimg --op=new --device-type=tape --barcode="A00000001" --size=10240 --type=data --file=A00000001"
#
# The tapes can be added after startup with
# "tgtadm --lld iscsi --mode logicalunit --op update --tid 1 --lun 4 --params element_type=2,address=1000,barcode=A0000001,sides=1"
# for slot 0 (is nr 1000)
#
# Please note that an MSL-2024 has no IMPORT/EXPORT elements (type 3)
include /etc/tgt/temp/*.conf
default-driver iscsi
<target iqn.2008-09.com.example:server.tape>
allow-in-use yes
#
# We need a backing store, although the tape drive will be empty,
# so we create a dummy tape "notape" in directory /root/tapes
# with the command "tgtimg --op=new --device-type=tape --barcode="" --size=1 --type=clean --file=notape"
#
<backing-store /root/tapes/notape>
lun 1
device-type tape
removable 1
vendor_id "HP "
product_id "Ultrium 3-SCSI"
product_rev "D21W"
scsi_sn "HU012345AB"
scsi_id "HP LTO3 ULTRIUM"
</backing-store>
#
# For the tape changer we need also a backing store, this can be a file containing zeros, like this:
# "dd if=/dev/zero of=$HOME/smc bs=1k count=1"
#
<backing-store /root/smc>
lun 4
device-type changer
removable 1
vendor_id "HP "
product_id "MSL G3 Series "
product_rev "3.00"
scsi_sn "ABC01234G3"
# Dummy 'page 0'
mode_page "0:0:0"
# Page 0x02: Disconnect/Reconnect SPC-3
mode_page "0x02:0:14:0x80:0x80:0:0xa:0:0:0:0:0:0:0:0:0:0"
# Page 0x1a: Power Condition SPC-3
mode_page "0x1a:0:18:0:0:0:0:0:0:0:0:0:0:0:0:0:0:0:0:0:0"
# Page 0x1c: Informational Exceptions Control SPC-3
mode_page "0x1c:0:10:8:0:0:0:0:0:0:0:0:0"
# Page 0x1d: Element Address Assignment SMC-3 7.3.4
mode_page "0x1d:0:0x12:0:0:0:0:0:0:0:0:0:0:0:0:0:0:0:0:0:0"
# Page 0x1e: Transport Geometry Parameters SMC-3 7.3.5
mode_page "0x1e:0:2:0:0"
# Page 0x1f: Device Capabilities SMC-3 7.3.2
# Page 0x1f/Subpage 0x41: Extended Device Capabilities SMC-3 7.3.3
mode_page "0x1f:0:0x12:0x0f:7:0x0f:0x0f:0x0f:0x0f:0:0:0:0:0x0f:0x0f:0x0f:0x0f:0:0:0:0"
# Type 1: Medium Transport Elements (robot arm/picker)
params element_type=1,start_address=1,quantity=1,media_home=/root/tapes
# Type 2: Storage Elements (tape slots)
params element_type=2,start_address=1000,quantity=24,media_home=/root/tapes
# Type 4: Add Data Transfer devices (drives)
params element_type=4,start_address=2,quantity=1,media_home=/root/tapes
params element_type=4,address=2,tid=1,lun=1
</backing-store>
</target>
|