/usr/share/doc/radvd/examples/radvd.conf.example is in radvd 1:2.11-1.
This file is owned by root:root, with mode 0o644.
The actual contents of the file can be viewed below.
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101 102 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 | #
# NOTE NOTE NOTE NOTE NOTE NOTE NOTE NOTE NOTE NOTE NOTE NOTE NOTE NOTE
# NOTE NOTE
# NOTE This is an EXAMPLE, which serves only to demonstrate the NOTE
# NOTE syntax of radvd.conf, and is not meant to be used for a NOTE
# NOTE real radvd configuration. NOTE
# NOTE NOTE
# NOTE NOTE NOTE NOTE NOTE NOTE NOTE NOTE NOTE NOTE NOTE NOTE NOTE NOTE
#
interface eth0
{
AdvSendAdvert on;
# This may be needed on some interfaces which are not active when
# radvd starts, but become available later on; see man page for details.
# IgnoreIfMissing on;
#
# These settings cause advertisements to be sent every 3-10 seconds. This
# range is good for 6to4 with a dynamic IPv4 address, but can be greatly
# increased when not using 6to4 prefixes.
#
MinRtrAdvInterval 3;
MaxRtrAdvInterval 10;
#
# You can use AdvDefaultPreference setting to advertise the preference of
# the router for the purposes of default router determination.
# NOTE: This feature is still being specified and is not widely supported!
#
AdvDefaultPreference low;
#
# Disable Mobile IPv6 support
#
AdvHomeAgentFlag off;
#
# example of a standard prefix
#
prefix 2001:db8:1:0::/64
{
AdvOnLink on;
AdvAutonomous on;
AdvRouterAddr off;
};
#
# example of a 6to4 prefix
#
# Note that the first 48 bits are specified here as zeros. These will be
# replaced with the appropriate 6to4 address when radvd starts or is
# reconfigured. Be sure that the SLA ID (1234 in this case) is specified
# here!
#
prefix 0:0:0:1234::/64
{
AdvOnLink on;
AdvAutonomous on;
AdvRouterAddr off;
#
# This setting causes radvd to replace the first 48 bits of the prefix
# with the 6to4 address generated from the specified interface. For example,
# if the address of ppp0 is 192.0.2.25 when radvd configures itself, this
# prefix will be advertised as 2002:C000:0219:1234::/64.
#
# If ppp0 is not available at configuration time, this prefix will not be
# advertised, but other prefixes listed in the configuration will be
# advertised as usual.
#
# When using the Base6to4Interface option, make sure radvd receives a
# SIGHUP every time the ppp0 interface goes up, down, or is assigned a
# new IPv4 address. The SIGHUP will cause radvd to recognize that the
# ppp0 interface has changed and will adjust the advertisements
# accordingly.
#
Base6to4Interface ppp0;
#
# If the IP address of ppp0 is assigned dynamically, be sure to set the
# lifetimes for this prefix to be small. Otherwise, hosts on your network
# may continue to use a prefix that no longer corresponds to the address
# on ppp0!
#
AdvPreferredLifetime 120;
AdvValidLifetime 300;
};
#
# example of a more specific route
# NOTE: This feature is not very widely supported! You may also need to
# enable it manually (e.g. on Linux, change the value of
# sysctl accept_ra_rt_info_max_plen to 48 or 64)
#
route 2001:db0:fff::/48
{
AdvRoutePreference high;
AdvRouteLifetime 3600;
};
#
# RDNSS
# NOTE: This feature is not very widely implemented.
#
RDNSS 2001:db8::1 2001:db8::2
{
AdvRDNSSLifetime 30;
};
#
# DNS Search Lists
#
DNSSL branch.example.com example.com
{
AdvDNSSLLifetime 30;
};
};
|